On high velocity hunting cartridges

There are endless stories of deer being killed with a rifle chambered in .22 LR. So if a little .22 LR is sufficient to kill a deer, why do we need anything more powerful? Isn’t .243 Winchester good enough? Isn’t .30-06 Springfield good enough? Why do we need this big-ass rounds like .300 Win Mag, and 7mm magnums? It’s not like they can make the deer any more deader.

Basically, shooting at longer distances.

An article from Field & Stream on the topic.

High velocity by itself does not kill anything, nor does it kill anything faster than standard velocity.

I started out believing devoutly in lots of speed, but 40 years later, having shot creatures of all sizes with just about everything that goes bang, I’ve never been able to find any correlation between bullet speed and sudden animal demise.

[…]

Not only do super-speed cartridges not kill any faster, but there are distinct disadvantages to them as well. First, let’s consider recoil and muzzle blast…. Second, when you get bullets traveling at 3000 fps and over—these days, way over—even the strongest and slowest-expanding of them makes a mess of whatever it hits…. Third, barrel life for the super-speed cartridges is considerably shorter than it is for standard-velocity loads.

[…]

Given all these drawbacks, why is it that high velocity keeps getting higher, and new and horrific super loads keep appearing? Because nothing makes hitting at long range easier than a good dose of feet per second. If you think you will need to take a shot at 300 yards and over, high velocity is your very best friend.

[…]

However, speed alone will not solve all your problems in hitting at long range. You also need resistance to wind drift and momentum, or the ability to sustain velocity way out there. The way you get it is by going not to light bullets that give the highest initial velocity—but to the heavier slugs in a given caliber, and to bullets that are streamlined.

So what it comes down to is context and selecting the appropriate tool for the context. If you’re out hunting big elk in the Rockies, 300 yard or more shots are likely and so a big gun helps. Here in Texas, 200 yards might be the extent of it and consider I’m working on a .223 Remington load for Texas whitetail and feral hogs. Heck, my father-in-law, who is a lifetime hunter, says that he’s tried just about everything out there over the years and he finds the .25-06 about the best thing for Texas hunting.

Like all things in life, you can pick the wrong tool for the job and still get the job done. But picking the right tool for the job often yields to the best and most satisfactory end results.

I’m so happy

Apparently I live in the 16th happiest state of our union.

Those poor Californians and New Yorkers.

Of course, today I’m happy for another reason. In a matter of hours life will return to “normal” (whatever that means). There will be much rejoicing and waving of little flags.

It bears repeating

From JayG:

Having a permit to carry a firearm doesn’t make you a tough guy. It’s not a license to shoot off your mouth, nor is it permission to let your guard down and be careless because, hey, you have a gun. It’s a deadly serious proposition that means you have to man up, put on the big boy pants, and let the loudmouth think he won the battle of wits. You have to be prepared to humble yourself to the jackass that wants to be the center of attention. You have to be ready to walk away, and to hell with what anyone thinks.

Having that gun doesn’t make you invincible. It makes you liable. If a fight happens, your best bet is to be in a different time zone. You don’t want there to be any chance you could get caught up in the excitement and have to make a life-or-death decision. You need to keep a clear head, one unsullied by drugs, alcohol, or foolish pride. You have to be the better person, no matter what that little devil on your shoulder whispers into your ear.

I’d say it doesn’t apply to just guns. If you’ve got legit abilities to hurt someone (e.g. martial arts training), it’s the same thing.

Just because you have a hammer, doesn’t mean everything’s a nail.

When you train for self-defense with firearms, the gun can become the answer to every problem.

When you train for self-defense with empty-hand martial arts, your fists can become the answer to every problem.

It’s the “when you have a hammer, everything looks like a nail” situation.

This is why good self-defense training involves running scenarios that can be resolved by alternative means.

Ikigai posts a story of a man trained in martial arts who was all too ready to solve a problem with his fists, but what ultimately solved the problem was an open ear and a caring heart. Read the story here.

I know. That sounds all sappy and schmaltzy, but it’s still a sound reminder that every situation is different and must be solved on its own merits. We must keep our minds and options open, because everything isn’t a nail.

Ugh

Of course after I order a can of Trail Boss I learn that you shouldn’t use Trail Boss with anything other than pure lead bullets (no jacketed, no plated). I can’t find the official statement from IMR/Hodgdon but it is implied in their Trail Boss description and some things I found online reinforce that Trail Boss should not be used with any sort of jacketed/plated bullet: all lead only.

I wanted it for .38 Special loads, but the only bullets I have right now are Berry’s plated. I guess I’ll have to pick up some cast semi wad cutters from The Bulletworks. I got to meet Jimmy Mitchell last year at a KR Training class. Great guy.

Whitetail Record

Check out this story about a (possible) record whitetail deer.

It could have the longest antler beams ever recorded.

He’s huge.

Lots of pictures at the above link, and the story of the buck too. Just awesome.

.38 Special reloads – round 2

Just did another round of .38 Special reloads.

Recalling the results of the the last batch, I had a tough time inserting the rounds into the chambers of the cylinder. I wondered if I belled the case-mouth too much, or if it could be from lack of crimp.

It was over-belling.

This time I did the smallest expansion I could. I could barely feel the difference in the case mouth. Measuring with calipers the mouth
expanded about 0.002″. But that’s all that was necessary, the bullet balanced just fine and seating it went smoothly. After seating, I dropped the round into the chamber and it went in and out without a hitch. Cool!

A few days ago I did pick up a Lee Factory Crimp die for .38/.357. Since I’m using these Berry’s plated bullets and given what I was told by the guy that consults for Berry’s, if any crimping is done it should be a light roll crimp or better would be a taper crimp. So I figured why not try the Lee Factory Crimp?

I loaded 30 rounds total. I used the same recipe I’ve been using (Berry’s .38 158 grain RN DS; 3.5 grains TiteGroup; Remington 1.5 SPP; CBC (Magtech) brass case; C.O.L. 1.510″). I left 15 uncrimped and I used a “light crimp” (1/2 turn, according to the die’s directions sheet) on the other 15. Let’s see how that goes. Not sure when I’ll get to the range to try this, but of course I’ll report the results.

What next?

Thinking out loud….

The goals of this .38 loading are two-fold. First, to just experiment and learn about reloading. Second, I’ve got a snub-nose class with Claude Werner in February 2010 and I’d like to have 400 (reloaded) rounds for that class. I’d like to do it because it sets a goal for me for my reloading work, plus shooting 400 rounds out of a snub over the course of the weekend… not sure how much that will beat up my hands. Having some sort of “mouse phart” load for the class wouldn’t necessarily be a bad thing.

I’m not going to change the bullet or the primers, and I’ll probably go with the same cases for now. Regarding cases, I don’t have 400 of the same case, but I do have over 400 cases. I understand the issues of how cases can vary, but my hope here is to keep the load mild. The gun is +P rated, so I think once I get a basic formula down the case variation ought not matter. So only thing I can think to vary would be the powder (type, amount) or the cartridge overall length.

I was thinking about the C.O.L.. I was trying to remember how I arrived at 1.510″; it might have been looking at the .38 Special “38 LRN 158 grain” data in the Speer #14 manual, as that’s listed as 1.510″. The Magtech 158 grain LRN that I have measures at 1.530″. The Remington UMC 130 grain JFN is I think 1.490″. Books say the maximum cartridge overall length is 1.550″. Other bullet shapes list lengths of 1.4xx”, usually in the mid-to-high .400’s. I might try some different lengths just to see the effect. For instance, try the max length of 1.550″. Try 1.490″. I know I could risk some higher pressures here so I want to keep things light in the powder end of things and not go too short. But I’d like to see how it changes the dynamics.

I’ll probably also try varying the powder. The lowest powder charge I saw for pure lead 158 grain was 3.2 grains of TiteGroup. That may not be enough for the plated Berry’s bullet (especially since I’m also loading with a longer COL and perhaps a light crimp), but I think it’s worth a try. Hodgdon’s data for TiteGroup says using a 158 grain Hornady XTP and COL of 1.455″, .38 Special max load is 3.9 grains of TiteGroup, .38 Special +P is 4.3 grains. Given that, I may try going up to 3.8 grains of TiteGroup or maybe even 4.0. We’ll see. Much to think about.

Damn hair farmers

So a 4-year-old — yes, 1… 2… 3… 4 years old — cannot attend classes because his hair is too long.

[Mesquite, Texas ISD officials] say the dress code prepares students for a business-orientated society where appropriate dress is critical.

Yet again we see how far out of touch school officials are with the rest of the world. Back in the 1950’s I’m sure “long hair” like this kid has probably could be held against you. Today? Pffft. I’ve had long hair for about 20 years and it hasn’t caused me any professional problems. I also don’t need to wear a suit and tie every day.

But the bigger question?

What sort of reasoning is that? This kid is 4-years-old. Four! What the hell are you doing preparing him for the business world? It wasn’t too long ago he learned to use the toilet on his own. His biggest concerns in life are getting another graham cracker, if today he’ll get to finger paint, and when is nap time. Good grief. Let the kid be a kid. About the only lesson for the real-(grown-up)-world you’re giving this kid right now is a healthy demonstration of how some adults can be douchebags.

But hey… yet another example of our failed public government school system.

Blogroll update

A long overdue update to the blogroll. Many of these sites I’ve been reading in my RSS reader for quite a while and I can only blame slack for not getting them in my roll sooner.

Pearls Before Swine

John Stossel @ RealClearPolitics

Rambling With Ruyter!

UrbanGrounds

SwissArmyWife

the munchkin wrangler.

Pervasivelight 5.0

Reason Magazine (their full RSS feed)

Bazillion Points Blog

The Volokh Conspiracy

Front Sight, Press

Rob Leatham’s Shooting Blog

Home On the Range

walls of the city

The Michael Bane Blog

Brillianter.com

the packing rat

Rustmeister’s Alehouse

New Jovian Thunderbolt

Snub Training

The Down Range Blog

Firearms and More in Texas!

Better and Better

Cranky Chicks with Guns

Schadenfreude

Politics, Guns, & Beer

MArooned

The Hog Blog

The AnarchAngel

Erik’s Web Spot

Baltimore Zen

things worth believing in

Low Tech Combat

Fighting Fit at Fifty

Kaiser Book Blog

Duckey’s Health Corner

Muay Thai: Beyond the Ring

Leavenworth Street